If you are procuring sensors for maritime and port operations in 2026, start by defining the operational environment and the data your systems need. The main decision is between inertial navigation systems that provide positioning and orientation when GNSS is degraded, and GNSS anti-interference systems that protect satellite signals in RF-congested areas. The TLH-INS-A vehicle positioning and directional navigation system and the WL-series GNSS anti-interference systems are two examples of options available on SkyDrone Max.
Key selection criteria for maritime and port sensors
Selection criteria should match the specific tasks your sensors will support—vessel positioning, container handling, autonomous guided vehicles, or port security patrols. Accuracy, environmental robustness, integration flexibility, and power requirements are the primary filters. For inertial navigation, review heading and attitude accuracy, position drift during GNSS loss, speed accuracy, and gyroscope stability. For anti-interference, review supported satellite signals, number of channels, operating voltage, and the number of broadband interferences the system can resist.
- Heading and attitude accuracy: The TLH-INS-A lists heading angle accuracy ≤0.1° (1 m baseline, dual antenna, satellite combination) and attitude angle accuracy ≤0.1°.
- Position drift during GNSS loss: The TLH-INS-A lists horizontal position accuracy ≤0.2% for GNSS loss of lock of 1 km or 120 s.
- Speed accuracy: The TLH-INS-A lists speed accuracy ≤0.1 m/s under satellite-guided combination.
- Gyroscope stability: The TLH-INS-A lists gyroscope zero bias stability (1 σ) ≤10°/h and scale nonlinearity ≤100 ppm.
- GNSS signal support: The WL181 processes BDS_B1/GPS_L1/Galileo/GLO_G1 signals; the WL80 processes 4-channel L1/G1; the WL669 processes 4-channel BDS_B1/GPS_L1.
- Interference resistance: The WL181 resists 6 broadband interferences; the WL80 and WL669 each resist 3 broadband interferences.
- Operating voltage: The WL181 operates at +18V~+32V; the WL80 and WL669 operate at +5V.
Trade-offs: inertial navigation vs GNSS anti-interference
Inertial navigation and GNSS anti-interference solve different problems, so the trade-off is not which is better but which capability your operation lacks. An inertial navigation system such as the TLH-INS-A integrates inertial navigation, satellite navigation (supporting RTK), and vehicle information. It supports dead reckoning and dual antenna orientation, and can integrate data from external odometry. This makes it suitable for autonomous driving, precision agriculture, assisted driving, robotics, logistics transportation, and special equipment. If your port vehicles or vessels need continuous heading and position during short GNSS outages—such as under crane shadows or in container stacks—an inertial system addresses that gap.
GNSS anti-interference systems, by contrast, protect the satellite signal itself. The WL181, WL80, and WL669 consist of antenna, RF, processing components, and receiver. They are designed to ensure high-precision positioning and timing under strong interference. If your port experiences RF congestion from other equipment, or if you need to harden an existing GNSS receiver against jamming, these systems are the relevant option. In practice, a maritime or port operation may need both: an anti-interference system to keep GNSS available, and an inertial system to maintain orientation and position when GNSS is briefly lost. Budget and integration complexity will determine whether you procure them together or in phases.
Integration questions to ask before purchase
Integration is where sensor projects succeed or stall. Ask the supplier how the sensor communicates with your existing control systems, what data protocols it supports, and whether it can accept external inputs. The TLH-INS-A can integrate data from various sensors such as external odometry, which helps if your vehicle already has wheel or shaft encoders. It also supports RTK and dual antenna orientation. For anti-interference systems, confirm how the antenna, RF, and processing components connect to your receiver, and whether the system is a complete unit or requires additional parts.
- What are the physical dimensions, weight, and mounting requirements? (Contact us for the datasheet if not listed.)
- What is the operating temperature range and ingress protection rating? (Contact us for the datasheet if not listed.)
- What input voltage and current draw should we plan for? The WL181 uses +18V~+32V; the WL80 and WL669 use +5V.
- Does the sensor output data in a format our navigation or control software can parse?
- Can the sensor be upgraded or recalibrated in the field, or does it require factory service? (Contact us for the datasheet.)
Procurement checklist for maritime and port sensor projects
- Define the operational scenario: vessel positioning, autonomous vehicles, crane guidance, or security patrol.
- List required accuracies for heading, attitude, position, and speed based on your use case.
- Determine whether you need dead reckoning capability and for how long (the TLH-INS-A lists 1 km or 120 s GNSS loss of lock).
- Identify GNSS signal types in your region and whether anti-interference is required (BDS_B1, GPS_L1, Galileo, GLO_G1, or L1/G1).
- Confirm power availability: +18V~+32V for WL181, or +5V for WL80 and WL669.
- Request datasheets for environmental ratings, dimensions, and connector types.
- Ask for integration support and whether external odometry or RTK corrections are supported.
- Plan for installation, calibration, and maintenance access in a salt-spray or high-vibration environment.
- Verify compliance with local maritime and port regulations—contact us for the datasheet if certification details are not listed.
Regional note: Southern Africa
For Southern Africa, port and maritime operations face heat, humidity, salt spray, and occasional RF congestion. These factors make environmental sealing and thermal tolerance important selection criteria. The supplied product data does not list ingress protection or temperature ranges, so confirm these with the supplier—contact us for the datasheet. If you operate in a port with heavy container traffic, multipath and signal blockage may make dead reckoning capability more valuable. If you operate near other RF transmitters, anti-interference capability may be the priority. The same sensor models can serve both needs, but the procurement emphasis will differ.
Example options and how to compare them
The table below summarizes the supplied data for the main product and related anti-interference systems. Use it to identify which category matches your requirement, then request full datasheets for the shortlisted models. Do not treat this table as a ranking; the products serve different functions.
| Attribute | TLH-INS-A | WL181 | WL80 | WL669 |
|---|---|---|---|---|
| Category | Sensors | Sensors | Sensors | Sensors |
| Model | LH-INS600M-21A系列 高精度组合导航系统 | WL181 | WL80 | WL669 |
| Brand | I-NAV Technology Co., Ltd. | SHENZHEN STARS TECHNOLOGY CO.,LTD | SHENZHEN STARS TECHNOLOGY CO.,LTD | SHENZHEN STARS TECHNOLOGY CO.,LTD |
| Type | Inertial navigation + GNSS | GNSS anti-interference | GNSS anti-interference | GNSS anti-interference |
| Key signals | Supports RTK, dual antenna | BDS_B1/GPS_L1/Galileo/GLO_G1 | 4-channel L1/G1 | 4-channel BDS_B1/GPS_L1 |
| Interference resistance | Not applicable | 6 broadband interferences | 3 broadband interferences | 3 broadband interferences |
| Operating voltage | Not listed—contact us for datasheet | +18V~+32V | +5V | +5V |
| Heading accuracy | ≤0.1° (1m baseline, dual antenna, satellite combination) | Not applicable | Not applicable | Not applicable |
| Position accuracy | ≤0.2% (GNSS loss of lock 1km or 120s) | Not applicable | Not applicable | Not applicable |
Featured product
TLH-INS-A vehicle positioning and directional navigation system
Product parameters: ① Heading angle accuracy: ≤ 0.1 °, 1m baseline; Dual antenna; Condition: Satellite combination ② Attitude angle accuracy: ≤ 0.1 ° ③ Horizontal position accuracy: ≤ 0.2% (GNSS loss of lock 1km or 120s) ④ Speed accuracy: ≤ 0.1 m/s (satellite guide combination) ⑤ Gyroscope zero bias stability (1 σ): ≤...
Products mentioned in this guide
WL181 dual-frequency seven-channel global navigation satellite system (GNSS) anti-interference system
The anti-interference system processes BDS_B1/GPS_L1/Galileo/GLO_G1 signals, with an operating voltage of +18V~+32V. It consists of antenna, RF, processing components and...
View product details →
WL80 Four-channel Global Navigation Satellite System (GNSS) Master Anti-interference System
The anti-interference system consists of antenna, RF and anti-interference components, is powered by +5V, can process 4-channel L1/G1 signals, counteract 3 broadband...
View product details →
WL669 Four-channel Global Navigation Satellite System (GNSS) Anti-interference System
The anti-interference system processes 4-channel BDS_B1/GPS_L1 signals, is powered by +5V, and includes antenna, RF, processing components and receiver. It can resist 3 broadband...
View product details →Frequently asked questions
What is the heading accuracy of the TLH-INS-A?
The TLH-INS-A lists heading angle accuracy ≤0.1° with a 1m baseline, dual antenna, under satellite combination.
Can the TLH-INS-A continue to provide position when GNSS is lost?
Yes, the TLH-INS-A supports dead reckoning. Its listed horizontal position accuracy is ≤0.2% for GNSS loss of lock of 1 km or 120 seconds.
What is the operating voltage of the WL181 anti-interference system?
The WL181 operates at +18V~+32V, according to the supplied product data.
How many broadband interferences can the WL80 resist?
The WL80 can resist 3 broadband interferences and processes 4-channel L1/G1 signals.
What satellite signals does the WL669 process?
The WL669 processes 4-channel BDS_B1/GPS_L1 signals and can resist 3 broadband interferences.
Need help selecting the right system?
Tell us your mission, payload, and operating environment. Our team will help you compare options and request the right datasheets from verified suppliers.